ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Topology Current Out Voltage Out (Max) Outputs and Type Efficiency @ Conditions Features Switching Frequency Component Count + Extras Design Author Application / Target Market Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (149)

149 Results - Page 1/15 |< < 1 2 3 4 5 > >|

LM3464EVAL: 4 Channel @ 350 mA/chan, 12~80V in

Manufacturer: Texas Instruments

This evaluation board demonstrates the high power efficiency and outstanding output current accuracy of the LM3464A typical application circuit. With four LED strings connected, the total output power is about 50W. The schematic, bill of material and PCB layout drawing of the LM3464A evaluation board are provided in this document.

View Design

TPS61150EVM-150: 4 LEDs x 2 @ 15mA, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

NCP3065D3SLDGEVB(2): 350mA @ 7 ~ 23V out, 8 ~ 25V in

Manufacturer: ON Semiconductor

* The eval board must be modified for 350mA output. The Transformer/Dual inductor and sense resistor(s). This circuit is intended for driving high power LEDs, such as the Cree XLAMP™ series, Lumileds Luxeon™ Rebel and K2 and OSRAM, Golden and Platinum Dragon™ as well as the OSTAR™.

View Design

LM3401-MR16DEMO: 1A @ 6.2V Max, 12VAC, MR16

Manufacturer: Texas Instruments

This design was developed to minimize the current spikes coming out of an electronic transformer to less than 5A, which is a typical transformer rating, when driving an LED MR16 circuit. The off the shelf LED MR16 solutions exhibit spikes that significantly exceed a transformers maximum rated output current which will degrade the reliability of the transformer and reduce its operating lifetime. T…

View Design

NCP3065D1SLDGEVB: 0.35, 0.7, or 1A @ 23V Max, 8 ~ 20V in

Manufacturer: ON Semiconductor

The NCP3065 is a monolithic switching regulator designed to deliver constant current for powering high brightness LEDs. The device has a very low feedback voltage of 235 mV (nominal) which is used to regulate the average current of the LED string. In addition, the NCP3065 has a wide input voltage up to 40 V to allow it to operate from 12 Vac or 12 Vdc supplies commonly used for lighting applicati…

View Design

STEVAL-ILL010V1: 1 ~ 6 LEDs @ 350 mA, 8 ~ 30V in

Manufacturer: STMicroelectronics

This evaluation board is designed around an L6902D-based DC-DC converter with dimming interface. The board implements both of two well known dimming methods: - Analog current control - Average current control by PWM

View Design

CAT4201AGEVB: 350mA @ 20V Max, 6.5 ~ 28V in

Manufacturer: ON Semiconductor

The CAT4201 is a high efficiency step-down LED driver from Catalyst Semiconductor. This device is designed to drive high brightness LEDs up to 350mA from a power supply up to 28V. The LED brightness is controlled by a single resistor from the RSET pin to GND. Analog dimming and idle mode control are available through the CTRL input. An external circuit is provided on the CAT4201AEVB for PWM dimmin…

View Design

STEVAL-ILL008V1: 1 LED @ 280mA, 0.6 ~ 5.5V in

Manufacturer: STMicroelectronics

The L6920D is used in this flashlight application as it is a high efficiency step-up controller that realizes the conversion from battery voltage to the selected output voltage with only three external components.

View Design

EVL6562A-LED: 350mA @ 45V Max, 36 ~ 60V in

Manufacturer: STMicroelectronics

Whenever a lighting application, such as street lighting for example, requires an elevated number of LEDs, there are basically two solutions: the first is to connect all the diodes in series in a single "string"; the second is to place several strings in parallel with fewer elements in each one.

View Design

LM3404HVEVAL: 1A @ Vin Max, 6 ~ 75V in

Manufacturer: Texas Instruments

The LM3404HV circuit and BOM have been designed to provide a constant forward current of 1.0A to a single LED with a forward voltage of approximately 3.7V from an input of 48V ±10%. Over the input voltage range of 6V to 75V the average LED current, IF, is 1.0A ±10%, the ripple current, ΔiF, will not exceed 400 mAP-P, and the switching frequency is 200 kHz ± 10%.

View Design
149 Results - Page 1/15 |< < 1 2 3 4 5 > >|